Historically, this is exactly how theological disputes were handled. See Crusades on Wikipedia for more information.

Before I start, I want to be clear, this process works for me. It isn’t for everyone, so take it with a grain of salt.

Outlining is personal. Everyone does it different. Some writers architect the full story, some outline the plot, while others discovery write everything. Personally, I get decision paralysis when I attempt to outline everything and when I attempt to discovery write everything.

When I start an outline, I tend to be detailed with setting and plot. I flush out my world and know roughly where I want the story to go. Characters are left fairly open. I create just enough of each character to get into their head. That way, I can take the characters, plop them into the setting and situation of the plot, and see what happenes. Discovery writing characters works for me, but only if I know where they are and what they should do.

Step 1: Sticky Notes… Starting out, I tend to brainstorm on sticky notes. There is something about writing ideas manually that helps me see things better than typing them. Typically, I have a vauge idea or two to start with, and not much more. I’ll write it on a sticky note and stick it to my desk. Then write something else - whatever comes to mind. I keep going until some ideas start to grow. It could be a character trait, plot point, setting, whatever. I’ll rearrange them to see what, if any, ideas make sense together. I’ll cross things out, throw some away, pull them from the trash, rewrite them, etc. Just an idea board type activity. Sometimes I will leave them on my deak for weeks. By the time I’m done with them, they are usually sad remnants of sticky notes.

Step 2a: Outline in Word… Word worked for me for a while. I created a template in Word that helps me straighten things out. It has custom headers that fill the Navigation panel, giving me sections. Default Word has this, I’ve just customized the look to something more pleasant to me. The problem is exactly what you said, things get lost. It grows fast and by the time I’m done with a full outline, it’s a little much.

Step 2b: Outline in OneNote… For the most part, I have transitioned to OneNote for the majority of my outlines. I created an always expanding template. It has tabs for things like Characters, Plot, Locations, Religion, Economy, Government, Magic, Weapons, Science, etc. I copy my template and start a new Notebook for each story I write. What I’m writing determines which tabs I keep. For example, if I am writing fantasy, I typically wont include the Science tab. Each tab has a page template that is automatically used when adding a new page. My character template, for example, has a table for physical traits, motivations, character arc, internal secrets, etc. I try to put down enough so I feel like I understand the person. Going overboard is easy, but I try to keep to to just what is needed.

Step 3: Scenes… Once I have a good understanding of the story, I start figuring out what scenes I need. These are typically one or two sentences and can help with plot, character development, or just something random and awesome. “A lazy pet cat that wakes up just in time to scratch the eyes out of an intruder.” I throw it in. Then, rearrange. Scenes never seem to come to me in an order that make sense. I’ll prune and expand, but by the time I’m done, I know the story.

Step 4: Fill in the blanks… I go one scene at a time, not necessarily in order, and fill them in. For example, Mr. Whiskers scratches Billy the Kid. Maggy sat straight up in her bed. The door banged agaist the cabin wall. Her eyes fought to stay closed as she forced them open. She couldn’t make out the silhouette in the door. The moonless night was no help. “You owe me money,” a gruff voice said. “Oh shit,” thought Maggie. She knew that voice. If Billy came to collect, she knew he would collect - one way or another. Billy took a step into the room. His boot was muffled by a thick layer of dust. Before he took a second step, a hissing filled the room. Mr. Whiskers sprung from the end of the bed. He landed on Billy’s face and started scratching the man like he was a mouse caught in the cupboard. And so on.

Step 5: Edit it together… Once you have I have all of the scenes, i stitch them together and edit it so it flows. This is where I add transitions and such. By the end, there is a completed story. It isn’t perfect. There might be some fillers, but it is about 95% done.

Step 6: Rewrite it all… I bring up a blank Word document, set it to 14pt Times New Roman, double spaced, and rewrite literally everything. I have my last draft and this one open side by side. Since I’m reading the story as I’m writing it, I notice thinga I missed or phrases I don’t like.

Again, this isn’t for everyone. It is a process that works for me.

It would take a lot to convince me that they haven’t been discussing this for years and have been waiting for the right time. The market is now loaded with others to do the delivery, which was probably one of the considerations. I’m sure another was how to announce it where they can blame someone else; at least to the point of ensuring some will defend them.

The minimum wage increase is their excuse. What they are doing is outsourcing their delivery to a 3rd party (GrubHub, Uber eats, etc). They wont have to pay them anything, the customer will. They are decreasing their head count, payroll, insurance, taxes, benefits, etc. They will lose some sales, but that wont even be close to their cost savings. They will easily make more money while selling their product at the same price. Any business would love to be in the same position.

I’m pretty sure NPM is Node Package Manager.

XNA, Microsoft’s C# based game dev framework, stood for XNA is Not Acronymed.

There isn’t enough in the picture to be 100% certain. In no particular order, these are the three things that I would check first:

1. The cable could be too short on that side
2. The track could be slightly too high on that side
3. The floor is angled and has a natural gap

My misunderstanding. I thought you meant from the heater to the floor.

To fix the gap you were talking about, you could do some acrylic caulking. You could do high heat silicone if you were worried about the heat, but the acrylic should be fine. Check the tube for the allowed heat range. The silicone will do vetter against the expansion and contraction, but you’d never be able to paint it. The acrylic would be paintable. But had a high chance of cracking.

You need the gap. Baseboard heaters work by heating the air around it, causing it to rise. This rising air is replaced by the cool air being displaced. By having a gap under the heater, the cool air has a place to go and be heated. This causes a draft that allows the full room to be heated, not just the area around the baseboards. In essence, the gap allows the heater to be more efficient.

If you insist on covering it, use a sheet of decorative metal that is at least partially open to allow airflow through it. Even that will reduce efficiency, but it wont be as bad as blocking it.

Why does my neighbor lock the door to his house? What if he is doing something in there I don’t agree with - like praying to a different god than me? How am I supposed to stop him? If I can’t just walk into his house whenever I want, I wouldn’t even know. This type of security can’t stand. Door locks are NSFWorld.

A quarter has 13 weeks, so if you do 2 week sprints and align them to start with a quarter, there is 1 week per quarter that is not accounted for. That week can be used for stuff outside of daily activities. It can be used for training, offsites, working on a pet project, etc. Its a good way to build time in the schedule for this type of thing. These types of breaks have tremendous long term value.

If you are using the concepts and writing the code yourself, you’re fine. If you are copying/pasting code from work to your personal project, you’re commiting IP theft. I’d recommend never doing that. On the otherhand, if it is for a peraonal project that you will never give away or sell, no one will know. Id still recommend not doing it, but to each their own.

That’s how a jury trial works. You need all 12 to agree, otherwise it is a hung jury and declared a mistrial. It is then up to the prosecutor to retry the case if they want to.

It isn’t double jeopardy because the trial didn’t come to a decision. If all 12 jury members agreed, one way or another, that is the end of it. At least for that/those counts.

I played a ton of 3d movie maker back in the day. I’m with you; I wish there were games like that today. It might be a niche, but you can’t tell me there isn’t a market for it.

AC as refrigerant, not coolant. Although that might be semantics.

AC is a type of heat pump. You are moving heat from inside to outside. The physics behind a heat pump, is fairly simple. There are three principles to work with.

1. Take a gas, compress it, and it gets super hot.
2. Take a compressed gas, let it rapidly expand, and it gets super cold
3. Different temperature gases move from hot to cold

Let’s focus on AC since most folks are used to that concept. In an AC, you have a closed loop of refrigerant. Outside, there is a compressor that compresses the gas, which makes it very hot. The gas is pushed through a radiator with a fan pulling air through it. Since hot moves to cold, the heat trapped in the gas moves to the outside air, and the gas is slightly cooled. (As long as the gas is hotter than outside).

Inside, there is an expansion valve that lets the gas rapdly expand, making it super cold. It is pumped through a radiator that has inside air blowing over it with a fan. Since hot moves to cold, the heat in the inside air moves to the cold gas, cooling the inside air. (As long as the gas is cooler than the inside temperature). It is then pumped outside to start the loop again.

So, inside gets cooler while the heat is moved outside. The physics also establishes the limits of the heat exchange. You will only grab heat from inside if the expansion makes the gas colder than the air inside. Typically it expands to around 0 degrees. Likewise, it will dump the heat outside if the gas is hotter than outside air. The compressor typically makes it 130 to 140 degrees (temps vary depending on many factors).

To use a heat pump for heating rather than cooling, reverse the process. Pick up the heat from outside and dump it inside. This will work as long as outside is warmer than the expanded gas (0 degrees or so). Although you can get some that go to around -20.

I’ll echo what others said about the aluminum tape. Make sure it is a good one, not a cheap one. You might want to take a damp rag to the area first. Any dust will stop it from sticking. Make sure to let it dry too.

Mastic could work as well. Get a tub of it and a chip brush or two… and don’t forget gloves. It sticks to everything and is rubberized, so it holds up very well. The only downside is that it makes a mess very easily.

More of a physical representation of a debt, but in essence, yes.

I buy a rock from you with $5, that $5 represents the debt I incurred by taking the rock. You have the $5 that you can use to barter for something else. At the end of the day, the government is backing my debt for the rock with a physical piece of paper. Except it isn’t physical anymore now that everything is digital. So, I suppose its more like the bits of data that represent the physical money that represents the debt for the rock is backed by the government. Although that money is actually physical at the bank that conducted the electronic transaction, and they borrowed that physical money from the fed. But even then, it is inflated since not every dollar a bank transacts with, is backed by something physical since the reserve ratio is not 100%. And that is when it starts becoming confusing.